Axiohm 7156 Specifikace

Procházejte online nebo si stáhněte Specifikace pro Tisk a skenování Axiohm 7156. Axiohm 7156 Specifications [en] Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 314
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků

Shrnutí obsahu

Strany 1 - Owner's Guide

NCR 7158 Thermal Receipt and Impact Printer Release 1.0 Owner's Guide B005-0000-1112 Issue D

Strany 2

viii Owner's Guide Chapter 7: Programming Guide Command Conventions...7-1 Li

Strany 3 - Preface

5-18 Chapter 5: Technical Specifications Print Zone Cut Edge44 Standard Columns = 71.5 mm (2.815 in.)56 Compressed Columns = 70 mm (2.756 in.) Cut Ed

Strany 4 - How to Use This Book

Chapter 5: Technical Specifications 5-19 When printing graphics or logos, converted from 6 dot/mm to 8 dot/mm (i.e. designed for 7156), the print

Strany 5 - Table of Contents

5-20 Chapter 5: Technical Specifications CharacterCharacterCell11 Dots1.368 mm0.054 in.13 Dots1.625 mm0.064 in.24 Dots3.00 mm0.118 in.19 Dots2.388 mm

Strany 6

Chapter 5: Technical Specifications 5-21 Receipt Throughput: Maximum throughput is achieved at any dot coverage up to 25%, which includes any amo

Strany 7 - Owner's Guide v

5-22 Chapter 5: Technical Specifications Allowable Duty Cycle (measured over one minute of continuous printing) Amount of Dot Coverage Ambient Temper

Strany 8

Chapter 5: Technical Specifications 5-23 Interface Description Human Interfaces • Receipt Paper-loading Door, on top of the cabinet. The receip

Strany 9 - Owner's Guide vii

5-24 Chapter 5: Technical Specifications FrontCoverSlip InLED (Green)Slip orCheckExtendedSlip TableReceiptReceiptCoverFront ofPrinterResetButtonFro

Strany 10

Chapter 5: Technical Specifications 5-25 DIP SwitchBack of PrinterOffSwitch 1 is shownin the ON positionOnDIP Switch4321 Location of Human and El

Strany 11 - Owner's Guide ix

5-26 Chapter 5: Technical Specifications Electrical Interfaces The 7158 RS-232C is equipped with a 9 Pin male D-shell connector, which will accept an

Strany 12

Chapter 5: Technical Specifications 5-27 Switch Settings These are out-of-service tests or printer settings invoked via the 4 position DIP switch

Strany 13 - Owner's Guide xi

Owner's Guide ix Additional Remote Diagnostics ...7-19 Comparison Chart...

Strany 14

5-28 Chapter 5: Technical Specifications Code Page 437

Strany 15 - Owner's Guide xiii

Chapter 5: Technical Specifications 5-29 Code Page 850

Strany 16

5-30 Chapter 5: Technical Specifications Code Page 852

Strany 17 - Revision Record

Chapter 5: Technical Specifications 5-31 Code Page 858

Strany 18 - Information to User

5-32 Chapter 5: Technical Specifications Code Page 860

Strany 19 - About the Printer

Chapter 5: Technical Specifications 5-33 Code Page 863

Strany 20 - Standard Features

5-34 Chapter 5: Technical Specifications Code Page 865

Strany 21 - Thermal Receipt Printer

Chapter 5: Technical Specifications 5-35 Code Page 866

Strany 22 - Impact Slip Printer

5-36 Chapter 5: Technical Specifications Dimensions and Weight 178 mm(7.0 in.)280 mm(11.0 in.)229 mm (9.0 in.)264 mm (10.4 in.)347 mm (13.7 in.)Exte

Strany 23 - Options

Chapter 6: Communication Interface Communication Overview In order for the printer to communicate with the host, a communication link must be set u

Strany 24 - Model Identification Key

x Owner's Guide Print and Eject Slip...7-36 Print and Carriage Return...

Strany 25

6-2 Chapter 6: Communication Interface Using BASIC to Send Commands In BASIC, printer commands are sent as a string of characters preceded by the LP

Strany 26

Chapter 6: Communication Interface 6-3 RS-232C Interface The RS-232C interface uses either the XON/XOFF (software) or DTR/DSR (hardware) protoc

Strany 27 - Setup Guide

6-4 Chapter 6: Communication Interface If the application sends data at 9600 baud and pauses between lines for as short a time as 50 milliseconds, t

Strany 28 - Choosing a Location

Chapter 6: Communication Interface 6-5 No Delay after Each Line Characters/Line Lines/Receipt Transmit Time (19.2 K Baud) Process Time* 20 20

Strany 29

6-6 Chapter 6: Communication Interface [DTR SPACE] - When ready to accept data. - Remaining space in the 4K buffer rises above 512 bytes. ** [XO

Strany 30 - 2-4 Chapter 2: Setup Guide

Chapter 6: Communication Interface 6-7 XON character = hexadecimal 11. XOFF character = hexadecimal 13. DTR/DSR Protocol The DTR signal is use

Strany 31 - Connecting the Cables

6-8 Chapter 6: Communication Interface Connector Pin-outs This section describes the pin settings for the connectors on the back of the printer. Com

Strany 32 - Cash Drawer Cables

Chapter 6: Communication Interface 6-9 Cash Drawer Connector A 6-contact modular jack (RJ11) is available to drive a cash drawer with dedicated

Strany 33 - Power Supply Cable

6-10 Chapter 6: Communication Interface

Strany 34 - Loading Receipt Paper

Chapter 7: Programming Guide Command Conventions The following information describes how each command is organized: Name: Name of command. ASCI

Strany 35

Owner's Guide xi Select or Cancel User-Defined Character Set ...7-58 Define User-Defined Characters...

Strany 36

7-2 Chapter 7: Programming Guide List of Commands and Location Commands control all operations and functions of the printer. This includes selecting

Strany 37 - Testing the Printer

Chapter 7: Programming Guide 7-3 Code (Hexadecimal) Command Page 16 n Add n Extra Dot Rows 39 17 Print 40 18 Open Form 23 18 Cancel Print D

Strany 38

7-4 Chapter 7: Programming Guide Code (Hexadecimal) Command Page 1B 34 m a0 a1 a2 Read from User Data Storage 147 1B 3A 30 30 30 Copy Character

Strany 39 - Using the Printer

Chapter 7: Programming Guide 7-5 Code (Hexadecimal) Command Page for MICR Read 1B 63 31 n Select Receipt or Slip for Setting Line Spacing 28 1

Strany 40

7-6 Chapter 7: Programming Guide Code (Hexadecimal) Command Page 1D 00 Request Printer ID 152 1D 01 Return Segment Number Status of Flash Memor

Strany 41 - Changing the Receipt Paper

Chapter 7: Programming Guide 7-7 Code (Hexadecimal) Command Page 1D 48 n Select Printing Position for HRI Characters 114 1D 49 n Transmit Pri

Strany 42

7-8 Chapter 7: Programming Guide By Function All items in BOLD are new or have additional functionality when compared to the 7156. Printer Function

Strany 43

Chapter 7: Programming Guide 7-9 1B 7A n Select or Cancel Parallel Printing Mode on R&J 32 1C Select Slip Station 33 1D 56 m Select Cut

Strany 44

7-10 Chapter 7: Programming Guide Horizontal Positioning Commands Code (Hexadecimal Command Page 09 Horizontal Tab 45 1B 14 n Set Column 45 1B 2

Strany 45 - Printing on Forms or Checks

Chapter 7: Programming Guide 7-11 Print Characteristic Commands Code (Hexadecimal Command Page 12 Select Double-Wide Characters 53 13 Select

Strany 46 - ORDER OF

xii Owner's Guide Transmit Peripheral Device Status ...7-86 Request Alternate Status (Parallel Only) ...

Strany 47

7-12 Chapter 7: Programming Guide Graphics Commands Code (Hexadecimal Command Page 1B followed by the BMP file data characters Download BMP Logo

Strany 48 - ENDORSE HERE

Chapter 7: Programming Guide 7-13 Real Time Code (Hexadecimal Command Page 10 04 n Real Time Status Transmission (DLE Sequence) 103 10 05 n R

Strany 49

7-14 Chapter 7: Programming Guide Page Mode Commands Code (Hexadecimal Command Page 0C Print and Return to Standard Mode/Print and Eject Slip 120

Strany 50 - Window Door

Chapter 7: Programming Guide 7-15 MICR Parsing Code (Hexadecimal Command Page 1B 77 50 Define Parsing Format, Save in NVRAM 132 1B 77 70 Defi

Strany 51

7-16 Chapter 7: Programming Guide Flash Download Commands Code (Hexadecimal Command Page 1B 5B 7D Switch Flash Download Mode 151 1D 00 Request

Strany 52

Chapter 7: Programming Guide 7-17 Comparison to 7156 New Features There are a number of new firmware features in the A758 Native Mode. These incl

Strany 53 - 60% of size)

7-18 Chapter 7: Programming Guide Additional character attributes The 7158 includes support for additional character attributes including Bold, Ital

Strany 54 - Printer Configuration

Chapter 7: Programming Guide 7-19 Macro Capability The 7158 supports the ability to record and execute a series of commands called a macro. Addit

Strany 55

7-20 Chapter 7: Programming Guide Comparison Chart The following table details the list of commands whose behavior differs from the 7156 because of

Strany 56 - Front Cover

Chapter 7: Programming Guide 7-21 Command Description Difference between 7156 and 7158 configured inA 756 Emulation Mode. Graphics scales the gra

Strany 57

Owner's Guide xiii Set Absolute Vertical Print Position in Page Mode...7-127 Set Relative Vertical Print Position in Page Mode...

Strany 58 - Communication Interface

7-22 Chapter 7: Programming Guide Command Descriptions Printer Function Commands The printer function commands control the following basic printer f

Strany 59 - Diagnostic Modes

Chapter 7: Programming Guide 7-23 Exceptions: In printers with the Parallel interface, this command also returns paper exhaust to the paper statu

Strany 60 - Receipt Test Mode

7-24 Chapter 7: Programming Guide Perform Full Knife Cut ASCII: EM or ESC i Hexadecimal: 19 or 1B 69 Decimal: 25 or 27 105 Cuts the recei

Strany 61 - MICR Test Mode

Chapter 7: Programming Guide 7-25 Return Home ASCII: ESC < Hexadecimal: 1B 3C Decimal: 27 60 Moves the impact printhead (unless already

Strany 62

7-26 Chapter 7: Programming Guide Initialize Printer ASCII: ESC @ Hexadecimal: 1B 40 Decimal: 27 64 Default: Receipt Slip Character P

Strany 63 - Check Flip Test Mode

Chapter 7: Programming Guide 7-27 Select Receipt or Slip for Printing; Slip for MICR Read ASCII: ESC c 0 n Hexadecimal: 1B 63 30 n Decimal:

Strany 64 - Emulation/Software Options

7-28 Chapter 7: Programming Guide Select Receipt or Slip for Setting Line Spacing ASCII: ESC c 1 n Hexadecimal: 1B 63 31 n Decimal: 27 99 49

Strany 65 - Hardware Options

Chapter 7: Programming Guide 7-29 Select Paper Sensors to Output Paper End Signals (Parallel Only) ASCII: ESC c 3 n Hexadecimal: 1B 63 33 n

Strany 66 - Check Flip Option

7-30 Chapter 7: Programming Guide Select Sensors to Stop Printing ASCII: ESC c 4 n Hexadecimal: 1B 63 34 n Decimal: 27 99 52 n Value of n : B

Strany 67 - Basic Troubleshooting

Chapter 7: Programming Guide 7-31 Enable or Disable Online Switch ASCII: ESC c 6 n Hexadecimal: 1B 63 36 n Decimal: 27 99 54 n Value of n

Strany 68

xiv Owner's Guide Request Printer ID...7-152 Return Segment Number Status of Flash

Strany 69 - Printer Beeps

7-32 Chapter 7: Programming Guide Generate Pulse to Open Cash Drawer ASCII: ESC p n p1 p2 Hexadecimal: 1B 70 n p1 p2 Decimal: 27 112 n p1 p2

Strany 70 - Printer Will Not Print

Chapter 7: Programming Guide 7-33 Select Slip Station ASCII: FS Hexadecimal: 1C Decimal: 28 Selects the Slip Station for all functions. Th

Strany 71

7-34 Chapter 7: Programming Guide Select Cut Mode and Cut Paper ASCII: GS V m GS V m n Hexadecimal: 1D 56 m 1D 56 m n Decimal: 29 86 m 29 86

Strany 72 - Poor Receipt Print Quality

Chapter 7: Programming Guide 7-35 Select Receipt Station ASCII: RS Hexadecimal: 1E Decimal: 31 Selects the Receipt Station for all functions. The

Strany 73

7-36 Chapter 7: Programming Guide Vertical Positioning and Print Commands The vertical positioning and print commands control the vertical print pos

Strany 74

Chapter 7: Programming Guide 7-37 Print and Carriage Return ASCII: CR Hexadecimal: 0D Decimal: 13 Prints one line from the buffer and feeds

Strany 75 - Knife Does Not Operate

7-38 Chapter 7: Programming Guide Feed n Dot Rows ASCII: NAK n Hexadecimal: 15 n Decimal: 21 n Value of n: Receipt Slip n/203 inch

Strany 76 - Other Serious Problems

Chapter 7: Programming Guide 7-39 Add n Extra Dot Rows ASCII: SYN n Hexadecimal: 16 n Decimal: 22 n Value of n: Receipt Slip n/203

Strany 77 - Returning a Printer

7-40 Chapter 7: Programming Guide Print ASCII: ETB Hexadecimal: 17 Decimal: 23 Prints one line from the buffer and feeds paper one line. Exec

Strany 78

Chapter 7: Programming Guide 7-41 Set Line Spacing ASCII: ESC 3 n Hexadecimal: 1B 33 n Decimal: 27 51 n Value of n: n/406 inches on rec

Strany 79 - Ordering Thermal Paper

Owner's Guide xv Uninstalling the Drivers ...8-17 Troubleshooting...

Strany 80 - Ordering Parts and Supplies

7-42 Chapter 7: Programming Guide Print and Feed Paper ASCII: ESC J n Hexadecimal: 1B 4A n Decimal: 27 74 n Value of n: n/203 inches recei

Strany 81 - Forms Specifications

Chapter 7: Programming Guide 7-43 Print and Feed n Lines ASCII: ESC d n Hexadecimal: 1B 64 n Decimal: 27 100 n Value of n: Number of li

Strany 82 - Ordering Documentation

7-44 Chapter 7: Programming Guide Reverse Feed n Dots ASCII: GS NAK n Hexadecimal: 1D 15 n Decimal: 29 21 n Value of n: n dots at 1/72 inc

Strany 83 - Technical Specifications

Chapter 7: Programming Guide 7-45 Horizontal Positioning Commands The horizontal positioning commands control the horizontal print positions of c

Strany 84

7-46 Chapter 7: Programming Guide Set Absolute Starting Position ASCII: ESC $ n1 n2 Hexadecimal: 1B 24 n1 n2 Decimal: 27 36 n1 n2 Value of n:

Strany 85 - Slip Forms - Recommendations

Chapter 7: Programming Guide 7-47 Set Horizontal Tabs ASCII: ESC D [n] k NUL Hexadecimal: 1B 44 [n] k 00 Decimal: 27 68 [n] k 0 Value of n

Strany 86

7-48 Chapter 7: Programming Guide Set Relative Print Position ASCII: ESC \ n1 n2 Hexadecimal: 1B 5C n1 n2 Decimal: 27 92 n1 n2 Value of n: T

Strany 87 - Standard Receipt Features

Chapter 7: Programming Guide 7-49 65,516/256 = 255, remainder of 236 n1 = 236 n2 = 255 To move to the right: Determine the value of n by multipl

Strany 88 - Bar Code Fonts

7-50 Chapter 7: Programming Guide Select Justification ASCII: ESC a n Hexadecimal: 1B 61 n Decimal: 27 97 n Value of n: 0, 48 = Left Aligned

Strany 89 - Optional Features

Chapter 7: Programming Guide 7-51 Set Left Margin ASCII: GS L nL nH Hexadecimal: 1D 4C nL nH Decimal: 29 76 nL nH Range of nL: 0 - 255 R

Strany 90 - Reliability

xvi Owner's Guide Radio Frequency Interference Statements Federal Communications Commission (FCC) Information to User This equipment has been tes

Strany 91 - Certifications

7-52 Chapter 7: Programming Guide Set Printing Area Width ASCII: GS W nL nH Hexadecimal: 1D 57 nL nH Decimal: 29 87 nL nH Range of nL: 0 –

Strany 92 - Slip Media

Chapter 7: Programming Guide 7-53 Print Characteristic Commands These commands control what the printed information looks like: selection of char

Strany 93 - Receipt Media

7-54 Chapter 7: Programming Guide Select 90 Degree Counter-Clockwise Rotated Print ASCII: ESC DC2 Hexadecimal: 1B 12 Decimal: 27 18 Rotates c

Strany 94 - Performance Requirements

Chapter 7: Programming Guide 7-55 Select Pitch (Column Width) ASCII: ESC SYN n Hexadecimal: 1B 16 n Decimal: 27 22 n Value of n: 0 = Stan

Strany 95 - Slip Format

7-56 Chapter 7: Programming Guide Set Character Right-Side Spacing ASCII: ESC SP n Hexadecimal: 1B 20 n Decimal: 27 32 n Range of n: 0 -

Strany 96 - Slip Throughput

Chapter 7: Programming Guide 7-57 Select Print Modes ASCII: ESC ! n Hexadecimal: 1B 21 n Decimal: 27 33 n Value of n: Pitch selection (st

Strany 97 - Character Format

7-58 Chapter 7: Programming Guide Related Information: The bits in this command perform the same function as the standalone functions: 1B 16 n Selec

Strany 98 - Ribbon Life

Chapter 7: Programming Guide 7-59 Define User-Defined Characters Receipt Slip ASCII: ESC & 3 c1 c2 n1 d1 ... nn dn ESC & 0 c

Strany 99 - Receipt Printing

7-60 Chapter 7: Programming Guide Defining User-Defined Characters for the Slip and Receipt Station Defines and enters downloaded characters into RA

Strany 100

Chapter 7: Programming Guide 7-61 n = 1-10 (standard pitch), 12 and less accepted but ignored n = 1-8 (compressed pitch), 12 and less accepted bu

Strany 101

Chapter 1: About the Printer Introducing the 7158 Printer The 7158 is an extremely fast, quiet, and reliable point-of-sale printer. It consists of

Strany 102

7-62 Chapter 7: Programming Guide Select or Cancel Underline Mode ASCII: ESC - n Hexadecimal: 1B 2D n Decimal: 27 45 n Value of n: 0, 48 = C

Strany 103 - Receipt Throughput:

Chapter 7: Programming Guide 7-63 Cancel User-Defined Characters ASCII: ESC ? n Hexadecimal: 1B 3F n Decimal: 27 63 n Value of n: Speci

Strany 104 - Receipt Paper Low:

7-64 Chapter 7: Programming Guide Select Double Strike A756 Emulation A758 Native ASCII: ESC G ESC G n Hexadecimal: 1B 47 1B 47 n Decimal:

Strany 105 - Interface Description

Chapter 7: Programming Guide 7-65 Select or Cancel Italic Print ASCII: ESC I n Hexadecimal: 1B 49 n Decimal: 27 73 n Value of n: 0 = Of

Strany 106

7-66 Chapter 7: Programming Guide Select International Character Set ASCII: ESC R n or ESC t n Hexadecimal: 1B 52 n or 1B 74 n Decimal: 27 82 n o

Strany 107 - Switch 1 is shown

Chapter 7: Programming Guide 7-67 Select or Cancel Unidirectional Printing Mode ASCII: ESC U n Hexadecimal: 1B 55 n Decimal: 27 85 n Value

Strany 108 - Electrical Interfaces

7-68 Chapter 7: Programming Guide Select or Cancel Upside Down Printing Mode ASCII: ESC { n Hexadecimal: 1B 7B n Decimal: 27 123 n Value of n

Strany 109 - Switch Settings

Chapter 7: Programming Guide 7-69 Select Character Size ASCII: GS ! n Hexadecimal: 1D 21 n Decimal: 29 33 n Value of n: 1 - 8 = vertica

Strany 110 - Code Page 437

7-70 Chapter 7: Programming Guide This command is effective for all characters (except for HRI characters). In Standard Mode, the vertical directio

Strany 111 - Code Page 850

Chapter 7: Programming Guide 7-71 Select or Cancel White/Black Reverse Print Mode ASCII: GS B n Hexadecimal: 1D 42 n Decimal: 29 66 n Valu

Strany 112 - Code Page 852

The product described in this book is a licensed product of NCR Corporation. NCR is a registered trademark of NCR Corporation. It is the policy of NCR

Strany 113 - Code Page 858

1-2 Chapter 1: About the Printer Standard Features Connectivity Features Industry standard RS-232C interface for communication with the host compute

Strany 114 - Code Page 860

7-72 Chapter 7: Programming Guide Select Superscript or Subscript Modes ASCII: AX ENQ n Hexadecimal: 1F 05 n Decimal: 31 05 n Value of n:

Strany 115 - Code Page 863

Chapter 7: Programming Guide 7-73 Summary of Rotated Printing The table shows the combinations of Set/Cancel Upside-Down Print, Set/Cancel Rotate

Strany 116 - Code Page 865

7-74 Chapter 7: Programming Guide Graphics Commands These commands are used to enter and print graphics data and are described in order of their hex

Strany 117 - Code Page 866

Chapter 7: Programming Guide 7-75 Select Bit Image Mode ASCII: ESC * m n1 n2 d1 ... dn Hexadecimal: 1B 2A m n1 n2 d1 ... dn Decimal: 27 42

Strany 118 - Dimensions and Weight

7-76 Chapter 7: Programming Guide In single density, one byte (7 dots) is printed in each full dot column; in double density, one byte is printed in

Strany 119 - Communication Interface

Chapter 7: Programming Guide 7-77 Top of Bit Image24-Dot Single-Density Mode—Receipt OnlydnMSBLSB d1 d2 d3 d4 d7 d5 d6 dn

Strany 120 - Using BASIC to Send Commands

7-78 Chapter 7: Programming Guide Select Double-Density Graphics ASCII: ESC Y n1 n2 d1 … dn or ESC L n1 n2 d1 ... dn Hexadecimal: 1B 59 n1 n

Strany 121 - RS-232C Interface

Chapter 7: Programming Guide 7-79 Select the Current Logo (Downloaded Bit Image) ASCII: GS # n Hexadecimal: 1D 23 n Decimal: 29 35 n Range

Strany 122 - 50ms Pause after Each Line

7-80 Chapter 7: Programming Guide Exceptions: This command is only valid for the receipt station. However, it will be processed correctly regardless

Strany 123 - RS-232C Communications

Chapter 7: Programming Guide 7-81 Define Downloaded Bit Image ASCII: GS * n1 n2 d1 ... dn] Hexadecimal: 1D 2A n1 n2 d1 ... dn] Decimal: 29

Strany 124 - XON/XOFF Protocol

Chapter 1: About the Printer 1-3 Thermal Receipt Printer • Extremely fast and quiet thermal printhead. • No ribbon or ink cartridge to change.

Strany 125 - DTR/DSR Protocol

7-82 Chapter 7: Programming Guide d1 d2 dn d Top of GraphicdnMSB LSBColumnColumn One 72 x 8 Max.RowOneRow 64Max. 64 65 d Exceptions: S

Strany 126 - Pin Numbers

Chapter 7: Programming Guide 7-83 Print Downloaded Bit Image ASCII: GS / m Hexadecimal: 1D 2F m Decimal: 29 47 m Value and Range of m: Val

Strany 127 - Cash Drawer Connector

7-84 Chapter 7: Programming Guide Convert 6 Dots/mm Bitmap to 8 Dots/mm Bitmap ASCII: AX EOT n Hexadecimal: 1F 04 n Decimal: 31 04 n Value:

Strany 128

Chapter 7: Programming Guide 7-85 Status Commands Status Command Introduction The 7158 has three methods of providing status to the application.

Strany 129 - Programming Guide

7-86 Chapter 7: Programming Guide Batch Mode For RS-232C printers, these commands enable the printer to communicate with the host computer following

Strany 130 - By Command Code

Chapter 7: Programming Guide 7-87 Request Alternate Status (Parallel Only) ASCII: ESC u n Hexadecimal: 1B 75 n Decimal: 27 117 n Value and

Strany 131 - BMP file data

7-88 Chapter 7: Programming Guide Transmit Printer Status ASCII: ESC v Hexadecimal: 1B 76 Decimal: 27 118 Sends status data to the host compu

Strany 132

Chapter 7: Programming Guide 7-89 Transmit Printer ID ASCII GS I n Hexadecimal 1D 49 n Decimal 29 73 n Value of n 1, 49 = Printer mode

Strany 133

7-90 Chapter 7: Programming Guide Type ID (n=4) Bit Off/On Hex Decimal Function 0 Off 00 0 No logo definition loaded by application. O

Strany 134

Chapter 7: Programming Guide 7-91 Transmit Printer ID, Remote Diagnostics Extension ASCII: GS I @ n Hexadecimal: 1D 49 40 n Decimal: 29 73

Strany 135

1-4 Chapter 1: About the Printer Impact Slip Printer • Bi-directional impact printhead designed for a very long life. • Snap-on ribbon cassette. •

Strany 136 - By Function

7-92 Chapter 7: Programming Guide Value of n Remote Diagnostic Item Function ASC Hex Dec “ 22 34 Serial # Not available, cannot clear Serial

Strany 137

Chapter 7: Programming Guide 7-93 Value of n Remote Diagnostic Item Function ASC Hex Dec â 83 131 Receipt lines tally Return receipt lines ta

Strany 138

7-94 Chapter 7: Programming Guide Value of n Remote Diagnostic Item Function ASC Hex Dec É 90 144 Hours on tally, 8 digit ASCII numeric, max

Strany 139

Chapter 7: Programming Guide 7-95 Value of n Remote Diagnostic Item Function ASC Hex Dec ¡ AD 173 Cover openings tally Write to NVRAM, and pr

Strany 140 - Status Commands

7-96 Chapter 7: Programming Guide Transmit Status ASCII: GS r n Hexadecimal: 1D 72 n Decimal: 29 114 n Value of n: 1, 49 = printer status

Strany 141 - Barcode Commands

Chapter 7: Programming Guide 7-97 Printer Status (n = 1 or n = 49) Bit Off/On Hex Decimal Status for Transmit Status 0 Off On 00 01 0 1 Rece

Strany 142 - MICR Check Reader Commands

7-98 Chapter 7: Programming Guide Slip Paper Status (n = 3 or n = 51) Value of Byte Returned Slip Status 0 There is no more printing space on the c

Strany 143 - User Data Storage Commands

Chapter 7: Programming Guide 7-99 Recognizing Data from the Printer An application sending various Real Time and non-Real Time commands to which

Strany 144 - Flash Download Commands

7-100 Chapter 7: Programming Guide Real Time Commands These commands provide an application interface to the printer even when the printer is not ha

Strany 145 - Comparison to 7156

Chapter 7: Programming Guide 7-101 Alternate Implementation The alternate implementation uses the DLE (0x10) sequences as implemented on other pr

Strany 146

Chapter 1: About the Printer 1-5 Options Connectivity Options • RS-232C is supported on all printers. USB is also supported on some later model

Strany 147 - Macro Capability

7-102 Chapter 7: Programming Guide Moving Data Through the Buffer Another consideration is that an application should take care not to let the buffe

Strany 148 - Comparison Chart

Chapter 7: Programming Guide 7-103 Real Time Status Transmission GS Sequence DLE Sequence ASCII: GS EOT n DLE EOT n Hexadecimal: 1D

Strany 149

7-104 Chapter 7: Programming Guide Related Information: 1 = Transmit Printer Status Bit Status Hex Decimal Function 0 Off 00 0 Fixed to Off 1

Strany 150 - Command Descriptions

Chapter 7: Programming Guide 7-105 3 = Transmit Error Status Bit Status Hex Decimal Function 0 Off 00 0 Fixed to Off 1 On 02 2 Fixe

Strany 151 - Open Form

7-106 Chapter 7: Programming Guide 5 = Transmit Slip Paper Status Bit Status Hex Decimal Function 0 Off 00 0 Fixed to Off 1 On 02 2 Fixed

Strany 152 - Generate Tone

Chapter 7: Programming Guide 7-107 Real Time Request to Printer GS Sequence DLE Sequence ASCII: GS ETX n or DLE ENQ n Hexadecimal:

Strany 153 - Return Home

7-108 Chapter 7: Programming Guide Recovers from an error after clearing the receive and print buffers. Print settings that are normally preserved f

Strany 154 - Set Slip Paper Eject Length

Chapter 7: Programming Guide 7-109 Real Time Printer Status Transmission ASCII: GS ENQ Hexadecimal: 1D 05 Decimal: 29 5 Transmits one byte

Strany 155

7-110 Chapter 7: Programming Guide Auto Status Back Select or Cancel Automatic Status Back ASCII: GS a n Hexadecimal: 1D 61 n Decimal: 29 97

Strany 156

Chapter 7: Programming Guide 7-111 The bits of n are defined in the table. Bit Off/On Hex Decimal Status for ASB 0 Off On 00 01 0 1 Cash dra

Strany 157

1-6 Chapter 1: About the Printer Model Identification Key A758 Model ID KeyA 7 5 8 - X X X X1 = no knife5 = knife0 = no MICR1 = MICR

Strany 158 - Bit Function

7-112 Chapter 7: Programming Guide First Byte (Printer Information) Bit Off/On Hex Decimal Status for ASB 0 Off 00 0 Not used. Fixed to off.

Strany 159 - Set Slip Paper Waiting Time

Chapter 7: Programming Guide 7-113 Third Byte (Paper Sensor Information) Bit Off/On Hex Decimal Status for ASB 0 Off On 00 01 0 1 Receipt pa

Strany 160

7-114 Chapter 7: Programming Guide Bar Code Commands These commands format and print bar codes and are described in order of their hexadecimal codes

Strany 161 - Select Slip Station

Chapter 7: Programming Guide 7-115 Select Pitch for HRI Characters ASCII: GS f n Hexadecimal: 1D 66 n Decimal: 29 102 n Value of n: Pitch

Strany 162 - M Feed and Cut Mode

7-116 Chapter 7: Programming Guide Values: First Variation: String terminated with NUL Character m = 0 – 6, 10 d = 32 - 126 (see the table) n =

Strany 163 - Print Test Form

Chapter 7: Programming Guide 7-117 The check digit is calculated for UPC and JAN (EAN) codes if it is not sent from the host computer. Six-charac

Strany 164 - Print and Eject Slip

7-118 Chapter 7: Programming Guide m Bar Code D n, Length 65 UPC-A 48- 57 (ASCII numerals) Fixed Length: 11, 12 66 UPC-E 48- 57 Fixed Leng

Strany 165 - Feed n Print Lines

Chapter 7: Programming Guide 7-119 Exceptions: Illegal data cancels this command. The command is valid only at the beginning of a line. PDF 417 f

Strany 166 - Feed n Dot Rows

7-120 Chapter 7: Programming Guide Page Mode Commands Page Mode is one of two modes, which the 7158 printer uses to operate. Standard Mode is typica

Strany 167 - Add n Extra Dot Rows

Chapter 7: Programming Guide 7-121 Cancel Print Data in Page Mode ASCII: CAN Hexadecimal: 18 Decimal: 24 Deletes all the data to be print

Strany 168 - Set Line Spacing to 1/6 Inch

Chapter 1: About the Printer 1-7 The set of options installed on a particular printer can be determined by looking at the printer's model nu

Strany 169 - Set Line Spacing

7-122 Chapter 7: Programming Guide Select Page Mode ASCII: ESC L Hexadecimal: 1B 4C Decimal: 27 76 Switches from Standard Mode to Page Mode.

Strany 170 - Print and Reverse Feed Paper

Chapter 7: Programming Guide 7-123 Select Standard Mode ASCII: ESC S Hexadecimal: 1B 53 Decimal: 27 83 Switches from Page Mode to Standard

Strany 171 - Reverse Feed n Lines

7-124 Chapter 7: Programming Guide Select Print Direction in Page Mode ASCII: ESC T n Hexadecimal: 1B 54 n Decimal: 27 84 n Value of n: Sta

Strany 172 - Reverse Feed n Dots

Chapter 7: Programming Guide 7-125 Set Printing Area in Page Mode ASCII: ESC W n1, n2 ...n8.] Hexadecimal: 1B 57 n1, n2 ...n8] Decimal: 27

Strany 173 - Set Column

7-126 Chapter 7: Programming Guide 4. dy = [(n7 + n8 x 256) x (vertical direction of the fundamental calculation pitch)] Keep the following notes i

Strany 174

Chapter 7: Programming Guide 7-127 Set Absolute Vertical Print Position in Page Mode ASCII: GS $ nL nH Hexadecimal: 1D 24 nL nH Decimal: 2

Strany 175 - Set Horizontal Tabs

7-128 Chapter 7: Programming Guide Set Relative Vertical Print Position in Page Mode ASCII: GS \ nL nH Hexadecimal: 1D 5C nL nH Decimal: 29 9

Strany 176 - Set Relative Print Position

Chapter 7: Programming Guide 7-129 Macro Commands These commands are used to select and perform a user-defined sequence of printer operations. St

Strany 177

7-130 Chapter 7: Programming Guide Execute Macro ASCII: GS ^ r t m Hexadecimal: 1D 5E r t m Decimal: 29 94 r t m Value of r: The number o

Strany 178 - Select Justification

Chapter 7: Programming Guide 7-131 MICR Commands MICR Reading These commands control the Magnetic Ink Character Recognition (MICR) check reader,

Strany 179 - Set Left Margin

1-8 Chapter 1: About the Printer

Strany 180 - Set Printing Area Width

7-132 Chapter 7: Programming Guide MICR Parsing This section describes MICR parsing in detail and includes several examples of useful parsing variat

Strany 181

Chapter 7: Programming Guide 7-133 Parsing Parameter String Options Variable Length Fields Variable Length Field Name Selector Comments Transit

Strany 182

7-134 Chapter 7: Programming Guide Other Parameters Error Number E One Digit Returned 0 1 Read OK Read error: bad character, empty field inva

Strany 183 - Select Pitch (Column Width)

Chapter 7: Programming Guide 7-135 Ten parameters are more than enough to specify all variable length fields with a field separator each and othe

Strany 184

7-136 Chapter 7: Programming Guide Sample Parsing Formats The following strings show various sample formats that you can use assuming they meet your

Strany 185 - Select Print Modes

Chapter 7: Programming Guide 7-137 ESC w p 018 x A <CR> • Always 18 characters in the account number with spaces and dashes replaced with

Strany 186

7-138 Chapter 7: Programming Guide ESC w p T '/ A '/ C '/ S <CR> • All characters in the transit number • Field separator: /

Strany 187

Chapter 7: Programming Guide 7-139 Notes All parameters are ASCII characters, i.e. greater than or equal to 0x20, with the exception of a non-ASC

Strany 188 - Station

7-140 Chapter 7: Programming Guide Once a parsing format is specified, the following values are returned: MICR Characters ASCII Hexadecimal Numeri

Strany 189

Chapter 7: Programming Guide 7-141 Check Serial Number Parsing the Check Serial Number Most banks print the check serial number in three easily r

Strany 190

Chapter 2: Setup Guide Unpacking the Printer Save all packing materials in case you need to repack the printer. Check that the materials shipped w

Strany 191

7-142 Chapter 7: Programming Guide If all of these searches fail to produce the distinct check serial number, and the check serial number field has

Strany 192 - Cancel Double Strike

Chapter 7: Programming Guide 7-143 Loading the Exception Table The exception table begins at word 20 in NVRAM. Each entry takes five words. There

Strany 193

7-144 Chapter 7: Programming Guide Exception Table Entry Format Each exception table entry consists of five words. The first two words contain the f

Strany 194 - Select Character Code Table

Chapter 7: Programming Guide 7-145 0 0 1 0 0 1 0 0 (check #, four characters) and 0 1 0 0 1 0 1 0 (account #, 10 characters) then stored

Strany 195

7-146 Chapter 7: Programming Guide which reads and returns word k in NVRAM. When the exception table is full, a new entry can replace an older, less

Strany 196

Chapter 7: Programming Guide 7-147 Read from User Data Storage ASCII: ESC 4 m a0 a1 a2 Hexadecimal: 1B 34 m a0 a1 a2 Decimal: 27 52 m a0

Strany 197 - Select Character Size

7-148 Chapter 7: Programming Guide Select Memory Type (SRAM/Flash) Where to Save Logos or User-Defined Fonts ASCII: GS " n Hexadecimal: 1D 22

Strany 198

Chapter 7: Programming Guide 7-149 Flash Allocation ASCII: GS " U n1 n Hexadecimal: 1D 22 55 n1 n2 Decimal: 29 34 85 n1 n2 Default

Strany 199

7-150 Chapter 7: Programming Guide Erase User Flash Sector ASCII: GS @ n Hexadecimal: 1D 40 n Decimal: 29 64 n Value of n: 49 - 50 Erases

Strany 200

Chapter 7: Programming Guide 7-151 Flash Download Commands These commands are used to load firmware into the printer. The commands are listed in

Strany 201 - Summary of Rotated Printing

2-2 Chapter 2: Setup Guide Choosing a Location 178 mm(7.0 in.)280 mm(11.0 in.)229 mm (9.0)264 mm (10.4 in.)347 mm (13.7 in.)ExtendedSlip TableRecei

Strany 202

7-152 Chapter 7: Programming Guide Request Printer ID ASCII: GS NUL Hexadecimal: 1D 00 Decimal: 29 0 Returns ACK (06 hex) + 12 bytes ASCII s

Strany 203 - Select Bit Image Mode

Chapter 7: Programming Guide 7-153 Select Flash Memory Sector to Download ASCII: GS STX n Hexadecimal: 1D 02 n Decimal: 29 2 n Value of n:

Strany 204 - Formulas:

7-154 Chapter 7: Programming Guide Return Microprocessor CRC ASCII: GS BEL Hexadecimal: 1D 07 Decimal: 29 7 Returns the CRC calculated over t

Strany 205

Chapter 7: Programming Guide 7-155 Erase Selected Flash Sector ASCII: GS DLE n Hexadecimal: 1D 10 n Decimal: 29 16 n Value and Range of n:

Strany 206 - Then Across)

7-156 Chapter 7: Programming Guide Download to Active Flash Sector ASCII: GS DC1 al ah cl ch d1…dn Hexadecimal: 1D 11 al ah cl ch d1…dn Deci

Strany 207

Chapter 7: Programming Guide 7-157 Reboot the Printer ASCII: GS (SPACE) Hexadecimal: 1D FF Decimal: 29 255 Ends the load process and reboo

Strany 208

7-158 Chapter 7: Programming Guide

Strany 209 - Define Downloaded Bit Image

Chapter 8: Universal Serial Bus About the Universal Serial Bus The Universal Serial Bus (USB) is a peripheral bus for personal computers that was f

Strany 210

8-2 Chapter 8: Universal Serial Bus Additional POS devices. Some POS systems are required to host more peripherals than can be supported by two RS-

Strany 211 - Print Downloaded Bit Image

Chapter 8: Universal Serial Bus 8-3 Checking for USB Support on the Host Computer To make USB work, the POS must be factory equipped with a USB p

Strany 212

Chapter 2: Setup Guide 2-3 Remove the Packing Restraints FrontCoverCardboardSupportCarriageFoamRestraint 1. Open the front cover, remove the

Strany 213

8-4 Chapter 8: Universal Serial Bus Note: Even though the host may have a USB port, Windows NT does not natively support plug-and-play USB because

Strany 214 - Batch Mode

Chapter 8: Universal Serial Bus 8-5 Configuring NCR POS Printers for USB Installing the NCR 7158 USB Upgrade Kit If you’re upgrading the printer,

Strany 215

8-6 Chapter 8: Universal Serial Bus 7. Return DIP switch No.1 to the original Off (down) position. 8. When you’re finished, plug the printer in ag

Strany 216 - Transmit Printer Status

Chapter 8: Universal Serial Bus 8-7 4. Remove the Options Board by gripping it at the connector end and lifting up. You may need to wiggle it s

Strany 217 - Transmit Printer ID

8-8 Chapter 8: Universal Serial Bus Configuring the Printer USB is a plug-and-play environment. As such, neither the printer nor the host requires u

Strany 218 - Type ID (n=4)

Chapter 8: Universal Serial Bus 8-9 DIP SwitchBack of PrinterOffSwitch 1 is shownin the ON positionOnDIP Switch4321 3. Open the Front Cover of t

Strany 219 - ASC Hex Dec

8-10 Chapter 8: Universal Serial Bus Follow the instructions on the scrolling menu, pressing the Paper Feed button to make selections. Indicate Yes

Strany 220

Chapter 8: Universal Serial Bus 8-11 8. Follow the instructions to select either XON/OFF or DTR/DSR, then skip the remaining communications para

Strany 221

8-12 Chapter 8: Universal Serial Bus Installing the USB Printer Drivers You must have LPIN D370-1111-0100 To install the required drivers to support

Strany 222

Chapter 8: Universal Serial Bus 8-13 2. To start the installation program, plug one end of the USB cable into the USB connector port on the prin

Strany 223

Owner's Guide i Preface Important Information to the User In order to ensure compliance with the Product Safety, FCC and CE marking requireme

Strany 224 - Transmit Status

2-4 Chapter 2: Setup Guide ReceiptCoverPaperRollPaper RollSupportsTe stPrintout 1. Open the receipt cover and remove the test printout. 2. Lif

Strany 225

8-14 Chapter 8: Universal Serial Bus Checking the Installation You’ll need to verify that the device drivers were installed correctly: Windows 95 an

Strany 226

Chapter 8: Universal Serial Bus 8-15 3. Scroll back up to “Ports.” You should see a COM number and port description for the NCR printer. If the

Strany 227

8-16 Chapter 8: Universal Serial Bus Configuring Serial Port Number Assignments This section described how the NCR USB solution assigns serial port

Strany 228 - Preferred Implementation

Chapter 8: Universal Serial Bus 8-17 Serial Port Configuration Methods Automatic (Default). When the printer is plugged into the USB port of the

Strany 229 - Alternate Implementation

8-18 Chapter 8: Universal Serial Bus Windows NT: Windows NT users will need to run the Edgeport Configuration Utility to uninstall the drivers. 1.

Strany 230

Chapter 8: Universal Serial Bus 8-19 Troubleshooting Problem Solution Device not working. Check for conflicting USB devices. Check

Strany 231

8-20 Chapter 8: Universal Serial Bus Frequently Asked Questions USB Printer Performance Under Windows 95 Normally sending output to a USB printer r

Strany 232 - 1 = Transmit Printer Status

Index—A— A758 printer advanced interface design, 1-2 configuration, 3-16 connectivity features, 1-2 description, 5-1 dimensions, 5-36 documentation,

Strany 233 - 3 = Transmit Error Status

Index-2 code page 850, 5-29 code page 852, 5-30 code page 858, 5-31 code page 860, 5-32 code page 863, 5-33 code page 865, 5-34 code page 866, 5-35 Ch

Strany 234

Index-3 Connecting cables cash drawer, 2-6 power supply, 2-7 Connector cash drawer, 6-9 RS-232C communication, 6-8 Consumables. See Paper Contacting a

Strany 235 - Real Time Request to Printer

Chapter 2: Setup Guide 2-5 Connecting the Cables Caution: Connect the cables to the printer before plugging in the power supply. If power is rec

Strany 236

Index-4 Humidity, 5-10 —I— Impact slip printer, 1-4 options, 1-5 Interface description, 5-23, 5-36 electrical, 5-26 human, 5-23 timing, 6-5 —J— Jams c

Strany 237 - Value of Byte:

Index-5 Ordering adapters, 4-2 cash drawers, 4-2 communication cable, 4-3 documentation, 4-4 paper, 4-1 power supply, 4-2 power supply cord, 4-2 ribbo

Strany 238 - Auto Status Back

Index-6 checks, 3-7 forms, 3-7 receipt, 5-17 slip, 5-12 Printing problems receipt, 3-34 Problems contacting a service representative, 3-38 flashing LE

Strany 239

Index-7 —S— Sample printout configuration menu, 2-12, 3-19 print test, 2-12 Sending commands BASIC, 6-2 DOS, 6-1 Service representative contacting, 3-

Strany 240

Index-8 —W— Weight, of printer, 5-36 —X— XON/XOFF protocol, 6-6

Strany 241

2-6 Chapter 2: Setup Guide Cash Drawer Cables The cash drawer cable connects the printer to one or two cash drawers. 1. Plug the cable into the ca

Strany 242 - Bar Code Commands

Chapter 2: Setup Guide 2-7 Power Supply Cable Connect the power supply cable last. 1. Plug the power cord into the power supply. Communicatio

Strany 243 - Print Bar Code

2-8 Chapter 2: Setup Guide Loading Receipt Paper 1. Tear off the end of the roll so that the edge is loose. 2. Place the roll into the paper buck

Strany 244

Chapter 2: Setup Guide 2-9 4. Remove the excess paper by tearing it against the tear-off blade. 5. Press the Paper Feed Button to advance th

Strany 245

2-10 Chapter 2: Setup Guide Putting In the Ribbon Cassette Note: You must use an approved NCR ribbon cassette with the check flip option to prevent

Strany 246

Chapter 2: Setup Guide 2-11 Testing the Printer The Configuration Menu allows you to set general printer parameters. The test prints a list of va

Strany 247 - Select Bar Code Width

2-12 Chapter 2: Setup Guide Configuration Menu and Print Test samples (shown approximately 60% of size). Caution: Be extremely careful changing a

Strany 248

Chapter 3: Using the Printer Printer Controls FrontCoverSlip InLED (Green)Slip orCheckExtendedSlip TableReceiptReceiptCoverResetButtonOn-Line,Paper

Strany 249 - Print Data in Page Mode

ii Owner's Guide How to Use This Book Use this book as a training guide for teaching users how to operate the printer or as a reference for progr

Strany 250 - Select Page Mode

3-2 Chapter 3: Using the Printer The printer also indicates its status when it is first turned on, or after it has been reset, by beeping. A single

Strany 251 - Select Standard Mode

Chapter 3: Using the Printer 3-3 Changing the Receipt Paper Change the paper when either a colored stripe appears on the receipt paper or the pri

Strany 252

3-4 Chapter 3: Using the Printer 1. Open the cover and remove the used roll. 2. Tear off the end of the new roll so that the edge is loose. 3. Pl

Strany 253

Chapter 3: Using the Printer 3-5 Replacing the Ribbon Cassette Change the impact printer’s ribbon cassette if it is printing lightly. Note: You

Strany 254

3-6 Chapter 3: Using the Printer 1. Open the printer’s front cover and pinch the tabs of the old ribbon cassette to remove it. RibbonCassetteKnobMy

Strany 255

Chapter 3: Using the Printer 3-7 Printing on Forms or Checks There are several types of transactions that may require the insertion of a form or

Strany 256

3-8 Chapter 3: Using the Printer Although the illustration on the following page shows a check being inserted into the printer, these instructions a

Strany 257

Chapter 3: Using the Printer 3-9 To print on a form or check: 1. Insert the form or check (check shown in the illustration) from the front and p

Strany 258 - Execute Macro

3-10 Chapter 3: Using the Printer Verifying and Validating Checks If the printer has the optional MICR check reader, checks are verified and then va

Strany 259 - MICR Commands

Chapter 3: Using the Printer 3-11 To verify and validate a check: 2. Place the check, face down on the Slip Table, with the bottom edge of the c

Strany 260 - MICR Parsing

Owner's Guide iii Table of Contents Chapter 1: About the Printer Introducing the 7158 Printer...

Strany 261 - Variable Length Fields

3-12 Chapter 3: Using the Printer Clearing Check Flip Paper Jams CheckCheck FlipWindow Door

Strany 262 - Other Parameters

Chapter 3: Using the Printer 3-13 To clear a paper jam from the optional check flip assembly: 1. Look in the window of the check flip assembly.

Strany 263

3-14 Chapter 3: Using the Printer Testing the Printer The Configuration Menu allows you to set general printer parameters. The test prints a list of

Strany 264 - Sample Parsing Formats

Chapter 3: Using the Printer 3-15 Configuration Menu and Print Test samples (show approximately 60% of size).

Strany 265

3-16 Chapter 3: Using the Printer Printer Configuration Printers are generally shipped with all appropriate configuration settings pre-set at the fa

Strany 266

Chapter 3: Using the Printer 3-17 • Hardware Options Print Density Maximum Power Knife Options Paper Low Sensor Printhead Resistance MICR Option

Strany 267 - Status Status Byte Value

3-18 Chapter 3: Using the Printer 1. Set DIP Switch 1 to On. Front of PrinterResetButtonFront Cover

Strany 268

Chapter 3: Using the Printer 3-19 2. Press the Reset Button while holding the Paper Feed Button. The printer beeps, prints the current configura

Strany 269 - Check Serial Number

3-20 Chapter 3: Using the Printer 4. Press the Paper Feed Button to make the selections. The instructions indicate whether to select something with

Strany 270

Chapter 3: Using the Printer 3-21 Diagnostic Modes This function allows the user to put the printer into the following diagnostic modes: • Norma

Strany 271

iv Owner's Guide Chapter 3: Using the Printer Printer Controls...

Strany 272 - Exception Table Entry Format

3-22 Chapter 3: Using the Printer 3. Run a transaction from the host computer. All commands and data sent from the host computer will be printed as

Strany 273

Chapter 3: Using the Printer 3-23 7. Exit the Configuration Menu. The printer is in Normal Mode and can communicate with the host computer. Sli

Strany 274 - Check Flip Command

3-24 Chapter 3: Using the Printer 2. After enabling the MICR Test Mode through the Configuration Menu, exit the Configuration Menu. 3. Insert a ch

Strany 275 - Read from User Data Storage

Chapter 3: Using the Printer 3-25 Check Flip Test Mode To run the Check Flip Test Mode: 1. Enable the Check Flip Test Mode through the Configura

Strany 276 - User-Defined Fonts

3-26 Chapter 3: Using the Printer 3. Push Paper Feed Button. The check then goes through the flip routine only—no printing takes place. To exit the

Strany 277 - Flash Allocation

Chapter 3: Using the Printer 3-27 Default Lines Per Inch This function allows the user to set the default lines per inch printed by the thermal r

Strany 278 - Erase User Flash Sector

3-28 Chapter 3: Using the Printer Knife Option This function makes it possible to set the Knife Option if it is installed in the printer. This setti

Strany 279

Chapter 3: Using the Printer 3-29 Basic Troubleshooting The 7158 printer is a simple, generally trouble-free printer, but from time to time minor

Strany 280 - Request Printer ID

3-30 Chapter 3: Using the Printer If something is wrong with the printer, take the following general steps: • Cycle the power of the printer and no

Strany 281 - Get Firmware CRC

Chapter 3: Using the Printer 3-31 Printer Beeps Problem/Symptom Possible Causes What to Do Printer beeps in a single, double, or triple pattern

Strany 282 - Erase the Flash Memory

Owner's Guide v Check Flip Option...3-28 Basic Troubleshooting...

Strany 283 - Erase Selected Flash Sector

3-32 Chapter 3: Using the Printer Printer Will Not Print Problem/Symptom Possible Causes What to Do The On Line, Paper Status, Error LED is blink

Strany 284

Chapter 3: Using the Printer 3-33 On-Line, Paper Status, Error LED Flashes Problem/Symptom Possible Causes What to Do On Line, Paper Status, Er

Strany 285 - Reboot the Printer

3-34 Chapter 3: Using the Printer Poor Forms Print Quality Problem/Symptom Possible Causes What to Do Printer starts to print, but stops while th

Strany 286

Chapter 3: Using the Printer 3-35 Thermal printhead is dirty. Improper internal cable connections. Printhead is defective. Use re

Strany 287 - Universal Serial Bus

3-36 Chapter 3: Using the Printer Slip Station, MICR and Flip Problems Problem/Symptom Possible Causes What to Do Slip Table LED does not come on.

Strany 288

Chapter 3: Using the Printer 3-37 Knife Does Not Operate Problem/Symptom Possible Causes What To Do Receipt is not cut. Paper is jammed. T

Strany 289 - Host Configuration

3-38 Chapter 3: Using the Printer Other Serious Problems The following problems all need to be corrected by a qualified service representative. See

Strany 290

Chapter 3: Using the Printer 3-39 Returning a Printer Follow these instructions if you need to return a printer for servicing. 1. If you are sen

Strany 291 - To update the firmware:

3-40 Chapter 3: Using the Printer a. Place receipt paper between the receipt cover and the printhead for protection. FrontCoverCardboardSupportCarr

Strany 292

Chapter 4: Printer & Media Supplies Ordering Thermal Paper Thermal Paper Specifications The printer requires qualified thermal paper with the f

Strany 293

vi Owner's Guide Standard Receipt Features...5-5 Optional Features ...

Strany 294 - Configuring the Printer

4-2 Chapter 4: Printer & Media Supplies Ordering Parts and Supplies Ordering Cash Drawers Order cash drawers from the following suppliers: Cash

Strany 295

Chapter 4: Printer & Media Supplies 4-3 Ordering Communication Cables Contact your sales representative to order the communication cables li

Strany 296

4-4 Chapter 4: Printer & Media Supplies Check Specifications Check American Standards ANSI X9.13 and ANSI X9.18, and International Standard ISO

Strany 297

Chapter 5: Technical Specifications Functional Description Standard Slip Features Print Technology Bidirectional, logic-seeking, nine wire impact p

Strany 298 - Installing the Drivers

5-2 Chapter 5: Technical Specifications Forms Capability * See notes on the following page. Maximum thickness .40 mm (.016 inch) max., 5 plies Minimu

Strany 299 - USB Cable Strain Relief

Chapter 5: Technical Specifications 5-3 Slip Forms - Recommendations The slip form should be flat and void of curls or wrinkles, especially at th

Strany 300 - Checking the Installation

5-4 Chapter 5: Technical Specifications Slip SideGuidePaper Holes andLow ReflectionProhibited AreasSlipEdge19 mm(0.747 in.)8 mm(0.315 in.)6 mm(0.236

Strany 301

Chapter 5: Technical Specifications 5-5 MICR Reader – Additional Information • The check must be flat and void of curls, folds, or wrinkles (esp

Strany 302 - Running the Edgeport Utility

5-6 Chapter 5: Technical Specifications Character Sets PC Code Page 437 PC Code Page 850 PC Code Page 852 PC Code Page 858 PC Code Page 860 PC Code P

Strany 303 - Uninstalling the Drivers

Chapter 5: Technical Specifications 5-7 Optional Features Paper Cutter Rotary partial cut knife leaves 5.0 mm (0.2 inch) uncut on left edge. Sli

Strany 304

Owner's Guide vii Electrical Interfaces ...5-26 Switch Settings...

Strany 305 - Troubleshooting

5-8 Chapter 5: Technical Specifications Reliability The numbers in the table refer to the Mean Cycles Between Failure (MCBF) for the items indicated.

Strany 306 - Frequently Asked Questions

Chapter 5: Technical Specifications 5-9 Certifications EMI: • FCC, Class A • Industry Canada, Class A • VCCI, Class A • CE Mark, Class B • A

Strany 307

5-10 Chapter 5: Technical Specifications Physical and Operating Environment Temperature and Humidity Temperature in Degrees %Humidity Operating:

Strany 308 - Index-2

Chapter 5: Technical Specifications 5-11 Minimum form length (feed direction) for forms inserted from the front up to the slip stop is 68 mm (2.6

Strany 309 - Index-3

5-12 Chapter 5: Technical Specifications Migration The 7158’s standard command set allows it to work with software written for NCR or other ESC/POS™

Strany 310 - Index-4

Chapter 5: Technical Specifications 5-13 Slip Format Maximum print line width: 120.7 mm (4.752 inches) starting 3.20 mm ± 1.5 mm (.125 inch ± .0

Strany 311 - Index-5

5-14 Chapter 5: Technical Specifications Slip Throughput Bi-directional line speed is based on a printhead speed of 260 CPS. Throughput (±5%) at the

Strany 312 - Index-6

Chapter 5: Technical Specifications 5-15 Character Format The 7158 can place 66 standard characters, or 80 compressed characters, or 33 rotated c

Strany 313 - Index-7

5-16 Chapter 5: Technical Specifications Dimension Standard Compressed Rotated mm inch mm inch mm inch A .36 .0144 .30 .0117 .36 .0144 B .35 .0

Strany 314 - Index-8

Chapter 5: Technical Specifications 5-17 Receipt Printing Receipt Format, 80mm Paper Width Print line width: 576 dots @ 8 dots/mm centered on 80

Komentáře k této Příručce

Žádné komentáře